Pag-iingat para sa pag-install at test machine ng hook type shot blasting machineï shotä¸ € ï¼ ‰

2021-06-03

Anghook type shot blasting machinesa pangkalahatan ay may isang mas malaking hitsura, at ang proseso ng pag-install ay medyo kumplikado kaysa sa maliit na kagamitan. Ang tamang pag-install at test machine ay ang susi upang matiyak ang normal na pagpapatakbo ng mga susunod na kagamitan. Sa kaso ng hindi sanay na paunang pagpapatakbo, kinakailangan ng mga gumagamit na mahigpit na sundin ang mga tagubilin ng nauugnay na tauhan o sumangguni sa mga tagubilin. Ang hindi pinahihintulutang pagpapatakbo ay maaaring madaling maging sanhi ng hindi maibabalik na pinsala sahook shot blasting machine. Angshot blasting machine manufacturer has sorted out the precautions for installation and test machine to share with you. I hope it will be helpful to users who use the device for the first time.
1. Installation. Anghook type shot blasting machine is installed and debugged in the production plant and disassembled into several parts before being transported to the user site for installation. Although there is no pit, the foundation must be firm, the anchor bolt holes must be standardized, and the chamber body must be adjusted. After the second irrigation, the anchor bolt nuts can be tightened after solidification. After the chamber body is fixed, the various parts can be installed. Angprecautions for the installation and debugging of the relevant components are introduced below.
1. Shot blasting aparato:
Angshot blasting device has been installed on the chamber body before leaving the factory. Please pay attention to the problems to be debugged before use. Check whether the fixed positions of the blade, the pill wheel, the directional sleeve, and the guard plate are accurate and firm, and check whether the direction of rotation is correct after power on. Then adjust the position of the directional sleeve opening. Theoretically, the angle between the front edge of the directional opening and the front edge of the blade throwing position is about 900. After fixing the position of the directional sleeve, the position of the projectile belt can be detected by hanging Place a steel plate or wooden board on the position of the workpiece facing the exit of the shot blasting machine, start the shot blasting machine, put a small amount (2-5kg) of projectiles into the blasting tube, and then stop, check whether the hit position on the steel plate is suitable for the needs, such as Close the window of the bias-adjustable directional sleeve downwards, and vice versa, until it fits, and note the position of the directional sleeve opening as a basis for future replacement of the directional sleeve.
2. Hoist at tornilyo conveyor:
Magsagawa muna ng walang pagsubok na walang pag-load upang suriin kung ang hoisting bucket at spiral blades ay tumatakbo sa tamang direksyon, pagkatapos ay higpitan ang sinturon ng hoist sa isang katamtamang antas ng pag-igting upang maiwasan ang paglihis, at pagkatapos ay magsagawa ng isang pagsubok sa pag-load upang suriin ang operasyon at kapasidad ng paghahatid, kung mayroong anumang pagiging kakatwa Ingay at panginginig ng boses, suriin at alisin ang mga hadlang.
3. separator ng Pill-sand:
Suriin muna kung ang paggalaw ng ram ay may kakayahang umangkop, at pagkatapos suriin ang tamang posisyon ng naghihiwalay na plato, pagkatapos kapag ang hoist ay na-load at na-debug, mayroong tuluy-tuloy na pag-agos ng mga shot ng bakal, at suriin kung ang mga pag-shot ng bakal ay umaagos at bumabagsak kapag ang chute ay natapos
  • QR
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy